Field-effect transistor biosensor with signal amplification by ternary initiation complexes for detection of wide-range RNA concentration.

Electrical detection of RNAs using transistor-based biosensors has attracted attention as a strategy for medical diagnosis and environmental monitoring. Herein, we demonstrated a proof-of-concept for specific, sensitive, and label-free RNA detection using a field-effect transistor (FET) biosensor with signal amplification by ternary initiation complexes (SATIC), which is an isothermal one-step nucleic acid amplification initiated by the combination of target RNA, circular DNA template and DNA primer. The SATIC system-applied FET biosensor specifically and quantitatively detected the target RNA with a single-nucleotide difference via the negative charges derived from the amplification products formed by a nucleic acid amplification reaction with φ29 DNA polymerase on the gate surface. In particular, the control of the amplification time allowed the detection of target RNA molecules over a wide concentration range, resulting in a detection limit of up to 6 copies/µL. Therefore, a transistor-based bioassay using the SATIC system could be useful for simple and sensitive nucleic acid analysis.

First-Principles Study on the Interplay of Strain and State-of-Charge with Li-Ion Diffusion in the Battery Cathode Material LiCoO2.

Cathode degradation of Li-ion batteries (Li+) continues to be a crucial issue for higher energy density. A main cause of this degradation is strain due to stress induced by structural changes according to the state-of-charge (SOC). Moreover, in solid-state batteries, a mismatch between incompatible cathode/electrolyte interfaces also generates a strain effect. In this respect, understanding the effects of the mechanical/elastic phenomena associated with SOC on the cathode performance, such as voltage and Li+ diffusion, is essential. In this work, we focused on LiCoO2 (LCO), a representative LIB cathode material, and investigated the effects of biaxial strain and hydrostatic pressure on its layered structure and Li+ transport properties through first-principles calculations. With the nudged elastic band technique and molecular dynamics, we demonstrated that in Li-deficient LCO, compressive biaxial strain increases the Li+ diffusivity, whereas tensile biaxial strain and hydrostatic pressure tend to suppress it. Structural parameter analysis revealed the key correlation of "Co layer distances" with Li+ diffusion instead of "Li layer distances", as ordinarily expected. Structural analysis further revealed the interplay between the Li-Li Coulomb interaction, SOC, and Li+ diffusion in LCO. The activation volume of LCO under hydrostatic pressure was reported for the first time. Moreover, vacancy formation energy calculations showed that the Li intercalation potential could be decreased under compressive biaxial strain due to the weakening of the Li-O bond interaction. The present findings may serve to improve the control of the energy density performance of layered cathode materials.

Facile one-pot synthesis of biomass-derived activated carbon as an interlayer material for a BAC/PE/Al2O3 dual coated separator in Li-S batteries.

Lithium-sulfur batteries (LSB) are an attractive alternative electrochemical energy storage device compared to conventional lithium-ion batteries due to their higher theoretical capacity and energy density. Despite these advantages, it is still difficult to commercialize LSB because of poor electrochemical performance caused by the dissolution of soluble lithium polysulfides (LiPS). To solve these critical issues, a multi-functional separator was prepared using biomass-derived activated carbon (BAC) and a ceramic layer on the polyethylene (PE) separator. For this purpose, BAC was synthesized by a facile one-pot synthesis method by a specifically designed furnace using various forms of milk waste. The multi-functional separator suppresses the effect of LiPS dissolution and increases the Li+ diffusion kinetics. BAC was able to absorb the LiPS shuttle, as confirmed by UV-vis measurements and X-ray photoelectron spectroscopy (XPS). LSB cells assembled using this multi-functional separator show a higher discharge capacity of 1092.5 mA h g-1 at 0.1 C-rate, while commercial PE separators deliver a specific capacity of 811.8 mA h g-1. These novel separators were also able to suppress lithium dendrites during cycling. This work offers a novel and simple approach for streamlining the synthesis process of BAC and applying it to LSB, aiding in the development of sustainable energy sources.

Tuning the Electronic, Ion Transport, and Stability Properties of Li-rich Manganese-based Oxide Materials with Oxide Perovskite Coatings: A First-Principles Computational Study.

Lithium-rich manganese-based oxides (LRMO) are regarded as promising cathode materials for powering electric applications due to their high capacity (250 mAh g-1) and energy density (∼900 Wh kg-1). However, poor cycle stability and capacity fading have impeded the commercialization of this family of materials as battery components. Surface modification based on coating has proven successful in mitigating some of these problems, but a microscopic understanding of how such improvements are attained is still lacking, thus impeding systematic and rational design of LRMO-based cathodes. In this work, first-principles density functional theory (DFT) calculations are carried out to fill out such a knowledge gap and to propose a promising LRMO-coating material. It is found that SrTiO3 (STO), an archetypal and highly stable oxide perovskite, represents an excellent coating material for Li1.2Ni0.2Mn0.6O2 (LNMO), a prototypical member of the LRMO family. An accomplished atomistic model is constructed to theoretically estimate the structural, electronic, oxygen vacancy formation energy, and lithium-transport properties of the LNMO/STO interface system, thus providing insightful comparisons with the two integrating bulk materials. It is found that (i) electronic transport in the LNMO cathode is enhanced due to partial closure of the LNMO band gap (∼0.4 eV) and (ii) the lithium ions can easily diffuse near the LNMO/STO interface and within STO due to the small size of the involved ion-hopping energy barriers. Furthermore, the formation energy of oxygen vacancies notably increases close to the LNMO/STO interface, thus indicating a reduction in oxygen loss at the cathode surface and a potential inhibition of undesirable structural phase transitions. This theoretical work therefore opens up new routes for the practical improvement of cost-affordable lithium-rich cathode materials based on highly stable oxide perovskite coatings.

Glycan-immobilized dual-channel field effect transistor biosensor for the rapid identification of pandemic influenza viral particles.

Pandemic influenza, triggered by the mutation of a highly pathogenic avian influenza virus (IFV), has caused considerable damage to public health. In order to identify such pandemic IFVs, antibodies that specifically recognize viral surface proteins have been widely used. However, since the analysis of a newly discovered virus is time consuming, this delays the availability of suitable detection antibodies, making this approach unsuitable for the early identification of pandemic IFVs. Here we propose a label-free semiconductor-based biosensor functionalized with sialic-acid-containing glycans for the rapid identification of the pandemic IFVs present in biological fluids. Specific glycans are able to recognize wild-type human and avian IFVs, suggesting that they are useful in discovering pandemic IFVs at the early stages of an outbreak. We successfully demonstrated that a dual-channel integrated FET biosensing system, which were modified with 6'-sialyllactose and 3'-sialyllactose for each gate area, can directly and specifically detect human H1N1 and avian H5N1 IFV particles, respectively, present in nasal mucus. Furthermore, to examine the possibility of identifying pandemic IFVs, the signal attributed to the detection of Newcastle disease virus (NDV) particles, which was selected as a prime model of a pandemic IFV, was clearly observed from both sensing gates. Our findings suggest that the proposed glycan-immobilized sensing system could be useful in identifying new pandemic IFVs at the source of an outbreak.

Effective induction of death in mesothelioma cells with magnetite nanoparticles under an alternating magnetic field.

With the objective of finding an avenue for development of magnetic hyperthermia as an effective mesothelioma treatment, the influence of heating by magnetite nanoparticles (MNPs) with a diameter of ~40nm, which were incorporated into cells and then subjected to AC magnetic field, on induction of cell death was investigated in all three histological subtypes of human mesothelioma cells (i.e., epithelioid NCI-H28, sarcomatoid NCI-H2052, and biphasic MSTO-211H cells). Cellular uptake of MNPs was observed in all cell types, but the amount of MNPs incorporated per cell into MSTO-211H cells was smaller than in NCI-H28 and NCI-H2052 cells. On the other hand, cell death induced by cellular uptake of MNPs was observed specifically in MSTO-211H cells. Hence, when cells are heated by intracellular MNPs under AC magnetic field, a high degree of cell mortality in NCI-H28 and NCI-H2052 cells is induced by the temperature increase derived from the high amount of intracellular MNPs, but the combination of intracellular heating and cell-type-specific toxicity of MNPs induced high rates of cell death in MSTO-211H cells even at a lower temperature. Almost all of the heated cells were dead after 24-h incubation at 37°C in all histological subtypes. Additionally, higher mortalities were observed in all three types of mesothelioma cells after MNPs-heating, as compared to the heating with a thermostatic bath. Herein, the significance of cellular uptake of MNPs for effectively inducing cell death in mesothelioma has been demonstrated in vitro.

Zinc-air battery: understanding the structure and morphology changes of graphene-supported CoMn(2)O(4) bifunctional catalysts under practical rechargeable conditions.

Nitrogen-doped/undoped thermally reduced graphene oxide (N-rGO) decorated with CoMn2O4 (CMO) nanoparticles were synthesized using a simple one-step hydrothermal method. The activity and stability of this hybrid catalyst were evaluated by preparing air electrodes with both primary and rechargeable zinc-air batteries that consume ambient air. Further, we investigated the relationship between the physical properties and the electrochemical results for hybrid electrodes at various cycles using X-ray diffraction, scanning electron microscopy, galvanodynamic charge-discharging and electrochemical impedance spectroscopy. The structural, morphological and electrocatalytic performances confirm that CMO/N-rGO is a promising material for safe, reliable, and long-lasting air cathodes for both primary and rechargeable zinc-air batteries that consume air under ambient condition.

A lithium-ion sulfur battery based on a carbon-coated lithium-sulfide cathode and an electrodeposited silicon-based anode.

In this paper, we report a lithium-ion battery employing a lithium sulfide cathode and a silicon-based anode. The high capacity of the silicon anode and the high efficiency and cycling rate of the lithium sulfide cathode allowed optimal full cell balance. We show in fact that the battery operates with a very stable capacity of about 280 mAh g(-1) at an average voltage of 1.4 V. To the best of our knowledge, this battery is one of the rare examples of lithium-metal-free sulfur battery. Considering the high theoretical capacity of the employed electrodes, we believe that the battery here reported may be of potential interest as high-energy, safe, and low-cost power source for electric vehicles.

On-chip fuel cell: micro direct methanol fuel cell of an air-breathing, membraneless, and monolithic design.

This paper proposes a novel design for a microfuel cell as an on-chip power source and demonstrates its fabrication and operation to prove the concept. Its simple design is important from the viewpoints of fabrication (e.g., replication), integration, and compatibility with other microdevices. In testing, the prototype cell was able to generate electric power (maximum: ca. 1.4 microW) on methanol without pumps under both neutral and acidic conditions. As for the size, the electrode part of the cell (two cathodes and one anode) is 400 microns in width and 6 mm in length. The evaluation demonstrated that the proposed design is a promising on-chip power source for miniature devices.

Perpendicular mesoporous Pt thin films: electrodeposition from titania nanopillars and their electrochemical properties.

A perpendicular mesoporous platinum electrode with a flat surface is successfully synthesized by electrodeposition using titania nanopillars as template, and the electrochemical studies indicate that this material is a promising catalytic electrode for fuel cells because of its high surface area and perpendicular nanopores.